What you put in, you'll get back ten fold
********We would like to take a moment of your time in thanking everyone that as helped us keep this forum going, from donations, sponsorship, hands on help and all the members that have used us, as it was built to help follow owners keep their passion on the roads, as we step into 2020 we hope all your hopes and dreams come true, we need to heart felt thank the owners that have given donations to help us carry on already so early into the new year and believing in what we are trying to do for everyone , it is also with great pride we thank AUTOLINKMX5 Mr Andrew Stott for sponsoring us again for this year, Andrew is not only a business but a very passionate petrol head and is always there to help fellow members in need regardless, the monthly discount code is always updated every end of the month with a fresh code so jump on getting it cheaper from us and Andrew , looking into this year we are hoping to arrange mazdamenders tech days/weekends this year to become the norm to meet and get our hands dirty all together, drive her like you stole her and weld that smile in place. *********
The mazdamenders team

Mk1 front break caliper overhaul

User avatar
flea
Site Admin
Posts: 6616
Joined: Wed Dec 07, 2011 8:42 pm
Location: Medway towns, Kent

Mk1 front break caliper overhaul

Postby flea » Thu Nov 29, 2012 5:52 pm

Mk1 front caliper overhaul.

After removing the front caliper from the car you'll need to remove the piston. I find it easier with a air hose. Put your hand behind the piston & it will stop it getting damaged also give short blasts from the air gun.
fc2.JPG
fc2.JPG (26.61 KiB) Viewed 1541 times

fc3.JPG
fc3.JPG (27.99 KiB) Viewed 1541 times


Then remove the dust cover from the housing as shown.
fc4.JPG
fc4.JPG (27.54 KiB) Viewed 1541 times

fc5.JPG
fc5.JPG (27.53 KiB) Viewed 1541 times


Then remove the inner rubber seal.
fc6.JPG
fc6.JPG (25.42 KiB) Viewed 1541 times

fc7.JPG
fc7.JPG (27.33 KiB) Viewed 1541 times

fc8.JPG
fc8.JPG (27.76 KiB) Viewed 1541 times


After removing the seals & throwing them away you need to clean the grooves shown in the picture near the end of my thumb, also the bore of the caliper body. You can use an air gun to ensure there is no debris left behind.
fc9.JPG
fc9.JPG (20.51 KiB) Viewed 1541 times


Also clean up the piston. I use flour paper as this will not scratch the finish but will remove the old rubber particles.
fc10.JPG
fc10.JPG (18.3 KiB) Viewed 1541 times


Fit the inner seal & make sure it is sitting properly & smear some brake fluid over the rubber.
I use the same fluid that I use in the braking system of the car.
fc11.JPG
fc11.JPG (23.9 KiB) Viewed 1541 times


Also smear some break fluid over the surface of the piston this will make it easier for you to fit the dust rubber.
fc12.JPG
fc12.JPG (17.06 KiB) Viewed 1541 times


Now push the dust rubber over the piston from the outer end. It will try to locate itself in the groove that its meant to sit in. Just push it over the groove to the other end of the piston so the rubber is sticking over the end as shown in the picture.
fc13.JPG
fc13.JPG (21.61 KiB) Viewed 1541 times


Now place the piston in front of the bore & locate the rubber at the bottom first, with your fingers work the rubber seal into the groove like so. You can give it a little twist holding your thumb & forefinger on the rubber to ensure it's in place.
fc14.JPG
fc14.JPG (23.15 KiB) Viewed 1541 times

fc15.JPG
fc15.JPG (21.97 KiB) Viewed 1541 times


Now just push the piston into the chamber. You'll feel it against the inner seal but it will go with a bit of pressure. The dust cover rubber will locate itself within the groove of the piston once pushed in enough. Just give it a check over to make sure its sitting properly.
fc16.JPG
fc16.JPG (22.81 KiB) Viewed 1541 times


Apply a little grease to the bleed screw & fit that.
fc17.JPG
fc17.JPG (27.09 KiB) Viewed 1541 times


And that's it your refurbished caliper.
fc18.JPG
fc18.JPG (23.26 KiB) Viewed 1541 times
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8

Return to “Braking”

Who is online

Users browsing this forum: No registered users and 1 guest