I am doing some research into the MX5/Eunos factory build codes to compile a power point list for anyone to use in the future on the restoration side, i need pics of the build stickers on the drivers side rear B post panel if they have not been removed already, no personal info will be shared ( vin...

Seen these on the bay of E and ordered the two biggest sizes they did,,,i think they are ace for the cost, largest made personal to you posted was £12, smaller one ( eunos ) was £8 i think, printed on aluminium , nice little touch to the garage...

Morning chaps and chapets ,,,,i have been going through my emails, messages,texts etc of the owners that need my help, they are not in any order as yet but can you check that i have not missed anyone please or what you need help with from also those that might have phoned and been missed as we...

Five weeks ago I began an experiment to find out what is the best way to remove rust from Brake Callipers ahead of reconditioning. Obviously other parts can be used but Callipers, rears in particular can be difficult to clean up with a wire brush and I wanted an easier method....

Hi Guys

I just acquired an ME221 ECU as the first stage of making my little MX5 go a bit faster.

Installation looks quite straightforward but I have one question about running a vacuum hose to the MAP sensor on the ecu.

All the images I can find suggest there should be a spare outlet on the...

Can’t beat pop up headlights IMO
7C1FF584-2060-4027-83F8-A739FF73FFD3.jpeg

Hi All,

Over the last 18 months or so I've had a number of rough running issues (MK2 2000 1.8 pretty much stock everything including the rust).

The first issue (not starting and rpm around 300 when it did) turned out to be a bad cam angle sensor - fixed.

Then a few months later the engine...

Hi All,

Just a quick one, where are you guys buying you Mk1 replacement / repair panels from? There appear to be a lot of places selling them and all sorts of discounts, I would be interested to hear anyone that's gone through this recently before I start trawling the world wide web! (If I do...

Oh dear, my car has just failed its MOT with a whole bunch of issues that I don't have time or skills to repair. So it is off to the great car park in the sky. :sad: :sad: :sad: :violin: :violin: :violin:

It has worn out rear tyres, (easily replaced and not a problem)
Floor excessively...

No doubt we have all heard about the governments crazy climate protection ideas, the most recent is the change from E5 unleaded to E10 unleaded.

I have heard that in respect of some older motorbikes, it is not recommended for them due to plastic tanks and certain fuel lines which can be severely...

Well, did anyone else get the top down today :handgestures-thumbup:

roof down pic.jpeg

Got these Wera bad boys spanner’s from Santa. Be interesting to try them out.

9F29650B-DD7E-4B28-9DB1-AEDEFB203F32.jpeg

Anyone got any experience of them?

I am sorry, but I feel the need to say something that I feel is bad service from an mx5 specialist here in the uk... I have personally hit this twice with them now. Items bought that have arrived with bits missing, that are needed (with the items) for fitting. Yet, they seem to do this as a norm,...

Treated myself to these Vessel JIS screwdrivers. Feel and look very good quality. Handles have a nice firm feel about them. There is also a nice knurled section on the metal blade rod.

Assuming early Mazdas used the JIS screw head pattern.
910E8B09-CFBD-4217-948F-9F92ECD9E31E.jpeg

Spoke to nice young lady on reception, "Not sure if I need parts or service for this but my shipping bungs aer missing from my 2018 MX5"
"ill put you thru to parts"
After a shoort pause
"Hello parts"
"Hi I am hoping you can help, the shipping bungs are missing...

Hi All

I had my car looked at by a specialist as part of a change of the cam cover gasket, and CAS-O ring.

It was idling high and the timing was modded to 14. It was all put back to standard. New plugs were fitted.

But idling has since been eratic. Nothing comes up on the diagnostic.

When...